產(chǎn)品詳情介紹
Fisher 646-34 電氣轉(zhuǎn)換器
1. Small Size—The small size and light-weight design of the transducer facilitate mounting and provide improved space utilization.
2. Vibration Resistance—The transducer, used in a standard valve/actuator mounted application, exhibits an output shift of less than 1 percent of span when tested to SAMA Standard PMC 31.1, Condition 3.
3. High Output Capability—The output volume of the transducer is adequate to drive valve/actuator combinations without requiring a positioner or volume booster.
4. Low Air Consumption—The transducer has low air consumption which cuts operating costs.
5. Easy Maintenance—Modular design of the converter allows easy replacement in the field for reduced maintenance costs.
6. Superior Performance—The accuracy, linearity, and frequency response coupled with minimal hysteresis far exceed the requirements of most control systems.
7. Mounting Position Insensitivity—The 646 transducer will operate in any orientation.
8. Specifications
8.1 Input Signal
4 to 20 mA DC, constant current with 30 VDC maximum compliance
voltage
8.2 Equivalent Circuit
The 646 equivalent circuit is a series circuit consisting of a constant
voltage drop (battery) of approximately 2.1 VDC and a total resistance
of 143 ohms. Input is shunted by three 6.8 V zener diodes
8.3 Output Signal
0.2 to 1.0 bar (3 to 15 psig) direct acting only
8.4 Supply Pressure(1)
Recommended: 1.4 bar (20 psig)
Minimum: 1.4 bar (20 psig)
Maximum: 3.4 bar (50 psig)
8.5 Maximum Steady-State Air Consumption(2)
Air consumption is proportional to output pressure. Maximum consumption at 1.0 bar (15 psig) output is 0.20 normal m3/hr (7.8 scfh).
8.6 Electrical Classification
Intrinsic Safety, Explosion Proof
9. Options
9.1 Output pressure gauge
9.2 Regulator, Gauge, 67CFR-224
1. Small Size—The small size and light-weight design of the transducer facilitate mounting and provide improved space utilization.
2. Vibration Resistance—The transducer, used in a standard valve/actuator mounted application, exhibits an output shift of less than 1 percent of span when tested to SAMA Standard PMC 31.1, Condition 3.
3. High Output Capability—The output volume of the transducer is adequate to drive valve/actuator combinations without requiring a positioner or volume booster.
4. Low Air Consumption—The transducer has low air consumption which cuts operating costs.
5. Easy Maintenance—Modular design of the converter allows easy replacement in the field for reduced maintenance costs.
6. Superior Performance—The accuracy, linearity, and frequency response coupled with minimal hysteresis far exceed the requirements of most control systems.
7. Mounting Position Insensitivity—The 646 transducer will operate in any orientation.
8. Specifications
8.1 Input Signal
4 to 20 mA DC, constant current with 30 VDC maximum compliance
voltage
8.2 Equivalent Circuit
The 646 equivalent circuit is a series circuit consisting of a constant
voltage drop (battery) of approximately 2.1 VDC and a total resistance
of 143 ohms. Input is shunted by three 6.8 V zener diodes
8.3 Output Signal
0.2 to 1.0 bar (3 to 15 psig) direct acting only
8.4 Supply Pressure(1)
Recommended: 1.4 bar (20 psig)
Minimum: 1.4 bar (20 psig)
Maximum: 3.4 bar (50 psig)
8.5 Maximum Steady-State Air Consumption(2)
Air consumption is proportional to output pressure. Maximum consumption at 1.0 bar (15 psig) output is 0.20 normal m3/hr (7.8 scfh).
8.6 Electrical Classification
Intrinsic Safety, Explosion Proof
9. Options
9.1 Output pressure gauge
9.2 Regulator, Gauge, 67CFR-224
所有評論僅代表網(wǎng)友意見，與本站立場無關(guān)。